Knoll HDP460 User Manual

HDP410 HDP420 HDP460 1080p DLP™ Projector Users Manual v1.3

10 Composite (RCA) video connection Plug the composite video cable’s yellow connector into the video-out connector on the video device. Plug the other

11 Computer connections You can connect a computer’s VGA connector to the M1-DA/DVI input on the projector using an M1-A cable. RS-232 connecti

12 Your projector has been factory optimized for adjust Picture menu options excellent performance no matter what the source.

13 The following tables show common problems. In some cases, more than one possible solution is provided. Try the solutions in the order they a

14

15 Still need assistance? If you need assistance, visit our website at www.knollsystems.com, or call us at 1 800 566 5579. during Pacific wes

16 Using the remote control The remote uses two provided AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning

17 • Turn on Overscan to remove noise on the edges of the video image (page 19). • Change the Aspect ratio (page18). Aspect ratio is the ratio of

18 Menu options are grayed out only if the source is selected but no signal is present. For example, if the projector is set to a video source but the

19 Gamma: Gamma tables contain preset intensity configurations optimized for the input source. You can select a gamma table that has been

2 FCC Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Ru

20 Color Space: this option applies to computer and Color space component video sources. It allows you to select a color space that has been spec

21 When Autosource is not checked, the projector defaults to Component initially, then defaults to whatever the last active source was when the p

22 Language: allows you to select a language for the onscreen display. • Custom key: allows you to assign a different functi

23 Maintenance Cleaning the lens 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. • Avoid using an excessive amount

24 7. Install the new lamp housing and tighten the screws. 8. Replace the lamp door. 9. Replace the base or ceiling mount plate, if necessary. S

25 Supported video formats RS-232 terminal specifications Communication configuration To control the projector from and LCD control panel

26 RS232 COMMAND FORMAT All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read reque

27 Supported commands Function Command Range Default Aspect Ratio ARZ 0-5 1 0 = Auto 1 = Native

28 Supported commands (continued) Function Command Range Default Gamma Table GTB 5 = Bright Room 7 = CRT 8 = PC Gr

29 SUPPORTED COMMANDS (CONTINUED) Function Command Range Default Power Up Source DSC 0-5 2 Presets PST 0-9

3 TABLE OF CONTENTS Safety Warnings 4 Introduction 5 Positioning the projector 7 Choosing the aspect ratio

30 LIMITED WARRANTY Knoll Systems, Inc. (“Knoll”) warrants that each HDP410, HDP420 and HDP460 (“the Product”) sold hereunder will conform to and func

4 Important Operating Considerations for Safety • Place the projector in a horizontal position no greater than 15 degrees off axis. • Locate the pr

5 Introduction Congratulations and thank you for your choice of a superior digital image projection device. Your new Knoll projector is specific

6 M1-DA/DVI 12 VDC triggers RS-232 IR input HDMI Rear Connector Panel

7 Setting up the Projector There are a number of factors to consider when determining where to set up the projector, including the size and shape

8 HDP410, HDP420 and HDP460 Projection Throw Distance 16:9 Video Screen: Screen Diagonal 92" 103" 106" 110" 122.5" 146.

9 Video Connectors Component RCA M1-DA/DVI 12 VDC triggers RS-232 IR input